personalised gifts for men

personalised gifts for men DIY Shower Cap with Optional Ribbon Rosette decorative pillow shams

Views:179 Updated: 2020-03-09

It’;s no secret that you love to sing in the shower…;and now you can do it in fabulous style. A bit of rip stop nylon and polyester chiffon will set the stage for an over-the-top, yet practical accessory. You can sing your heart out secure in the knowledge that your hair will emerge impeccable!

Supplies

personalized pillow cases

Step 1) Make your pattern.

Cut a piece of string about 18″ long.

Tie one end to a dowel or chopstick and the other to the pen so the string measures 9″ between the two.

Holding the point of the dowel in place in the center of the paper piece, pull the string taut so there is no slack.

Move the pen in a circle, keeping the string taut, and draw a circle.

Cut out the circle; this is your pattern piece.

Tip: Tape several pieces of paper together to make one large sheet, or use newspaper for your pattern.

Tip: Be sure to use string, not yarn. Yarn stretchespersonalised gifts for men, which will make your circle larger than intended.

Tip: Before drawing your circle, make a mark at the center (where the dowel is). If your dowel moves, you can easily get “back on track.”

Step 2) Cut your fabric.

Using your paper pattern piece, cut one circle from ripstop nylon and one from chiffon.

Cut an 18-1/2″-long strip of elastic.

Step 3) Construct the shower cap.

Note: All seam allowances at ?” unless otherwise noted.

With right sides together, sew the circles together, leaving an opening for turning. If you are using pins, keep them within the seam allowance to avoid making permanent holes in the ripstop nylon.

Trim the seam allowances, being sure not to cut into the stitching. This will help keep the elastic from getting hung up on the seams. In addition, as they are visible through the sheer chiffon, this will neaten the appearance on the right side of the shower cap.

Turn the cap right side out?through the opening.

Using low heat, carefully iron the seam along the outer edge of the cap. Alter

Create a channel for the elastic by sewing 1/2″ away from the finished edge.

Insert elastic through the opening.

Overlap the edges by 1/4″ and stitch the ends together.

Slipstitch the opening closed.

Distribute the fullness evenly around the cap.

Step 4) Construct the ribbon rosette.

Cut a 3″-wide strip of chiffon as long as desired. The rosette in the photographs used a 34″-long strip.

Tip: The fullness of your finished flower is dependent on the length of your strip: a short strip (around 25″) will make a small flower, while a 60″ strip will create a large, full rosette.

With wrong sides together, fold the strip in half lengthwise.

If desired, finish the edge with a small zigzag stitch to prevent fraying.

Using the longest straight stitch available on your machine (generally 5.0 mm), sew ?″ away from the raw edges of the strip. Leave thread tails on both ends of the strip.

On one end of the strip, knot the thread tails together. This will prevent the threads from pulling through the material.

At the other end of the strip, pull on the bobbin thread and begin tightly gathering the fabric strip. The fabric will begin curling in on itself, creating a flower-like appearance.

When finished gathering, knot the thread tails.

Using a hand-sewing needle, tack the ruffled flower layers together.

If desired, add a button to the center of the rosette.

Tack the rosette to the shower cap, or make it removable by hot-gluing a pin back to the underside.

Tip: Make several showercaps to give away, using different chiffon prints for each one.

Couching is a sewing technique where thread, fabric or yarn is attached to a piece of fabric. It's traditionally sewn by hand but a machine with a zig zag stitch can be used.In this Instructable I share an easy way to do couching with yarn using a sewing machine.I also provide additional information to make a simple and unique couched quilt.


personalized gift for Grandpa